-
Safety matters during daily operation of hot melt glue machine
Jul 26 , 2021
Safety matters during daily operation of hot melt glue machine： 1. Avoid operating the hot melt glue machine around volatile and explosive materials or gases, and do not store flammable and explosive materials around the spraying equipment of the hot melt glue machine. 2. Do not operate the hot melt glue machine without proper protection devices, good insulators or good pr...
Read More
-
Introduction of hot melt glue hose
Jul 30 , 2021
1.The use of imported Teflon liner, has good flexibility, good bending performance (maximum bending radius of 20cm), anti-sticking and temperature resistance (up to 220 degrees), can greatly reduce the carbonization phenomenon; 2.The heater by the United States and the temperature of the heating wire lines, evenly wrapped around the pipe wall, with good insulation and uniform thermal conductivity,...
Read More
-
Linear glue line type automatic nozzle
Jul 31 , 2021
Thread spray guns are also called strip spray guns or point spray guns, which are widely used in dispensing or spraying glue on packaging. Product Features: Combination custom linear spray gun features: 1.The gun body has a built-in filter to enhance the filtering effect and realize the point and strip sizing effect; 2. Diversified nozzles can be provided to solve the application of glue spraying ...
Read More
-
Hot melt adhesive glue
Aug 04 , 2021
Hot melt adhesive is a 100% solid, which becomes molten after heating, and it condenses when it contacts the air when it meets the cold surface, and then it only takes a few seconds to finish. Compared with solvent-based and water-based solvents, the primary benefits are as follows: 1. After a short time, to ensure high-efficiency production. 2. No need for drying equipment, saving space. 3. Non-t...
Read More
-
The reason why the hot glue can be melted
Aug 05 , 2021
It may be a very complicated situation that the hot melt adhesive cannot be melted. It is the result of the mixing of the above reasons. There are many carbides in the glue furnace, which will cause inaccurate temperature control of the equipment for a long time. Even if the glue furnace is cleaned regularly later, but the temperature control of the equipment has long been damaged, it is difficult...
Read More
-
The reason why the sealing machine is not strong
Aug 14 , 2021
1. Material selection of the box: The selection error mainly refers to the imperfect matching of the hot melt adhesive or the type of boxes that need to be bonded, and it is difficult to meet the process requirements of the material itself. 2. The temperature during compounding does not meet the requirements: The compounding temperature does not reach the melting point of the adhesive film or omen...
Read More
-
The reason why the hot melt glue machine does not heat up
Aug 16 , 2021
With the change of the times, mechanization is getting closer and closer to life. Most of the products used in life need to be bonded to form objects. The glue required for traditional bonding has been gradually eliminated with the strengthening of environmental protection awareness, and the environmental friendly hot melt adhesive has gradually appeared in the public view, Among them, the essenti...
Read More
-
Installation of Hose & Nozzle Assembly
Aug 20 , 2021
1.Fix the nozzle assembly horizontally or vertically in a proper place (assembly line,a desktop shelf,etc) with a Ф0.5” steel stick. Keep the nozzle facing the area to be sprayed or injected or coated. Note:When removing or installing nozzle assembly,extreme care should be given to protect the nozzle. 2.Connect one side of the hose to the outlets of manifold,and tighten the connection part with a ...
Read More
-
How to maintain the book binding hot melt adhesive machine
Aug 23 , 2021
How to maintain the book binding hot melt adhesive machine? Firstly, we have the most important point about how to operate the book binding hot melt adhesive machine, which must be operated by a specially assigned person. Then, we need to maintain the hot melt adhesive machine regularly. The following points need to be paid attention to when maintaining the hot melt adhesive machine. 1. Regularly ...
Read More
contact us
