-
What should we do if the gear pump hot melt glue machine suddenly does not produce glue during use?
Oct 28 , 2021
There are two types of hot melt glue machines, one is piston pump hot melt glue machine and the other is gear pump hot melt glue machine. These two hot melt glue machines have their own advantages. The following is mainly about gear pump hot melt glue. This type of machine is suitable for processes that require continuous glue production. If glue is not produced midway, it will have a great impact...
Read More
-
Requirements for hot melt hoses in the process of using hot melt glue machines
Oct 28 , 2021
Each set of hot melt glue machine equipment needs a hot melt hose as a delivery pipe to transport the hot melt glue melted into a liquid state in the host to the glue gun. Don't look at it as just a conveying pipeline,pay attention to it, in fact, there are requirements for it in the process of use. The most used one is made of Teflon inner tube. Firstly, it is required to be able to withstand hig...
Read More
-
How to install the hot melt glue gun on the hot melt glue machine
Oct 29 , 2021
Before using the hot melt glue machine equipment, you need to install a hot melt hose and a manual hot melt glue gun. The installation of the hot melt glue gun is relatively complicated, but it is also very simple. 1. The installation staff need to wear protective gloves to avoid scratches 2. Use a wrench to tighten the thread connecting the hot melt glue gun and the hot melt hose 3. Insert the po...
Read More
-
How hot melt glue machine apply hot glue
Oct 29 , 2021
Because of the environmental protection of hot-melt adhesives, more and more industries are required to use hot-melt adhesive bonding materials. How does the hot-melt adhesive machine use hot-melt adhesive? Hot melt adhesive is solid, and it needs to be heated and melted into a liquid state in order to use it. The hot melt glue machine has a melt box, and the hot melt glue can be melted by pouring...
Read More
-
What affects the sticking effect of hot melt glue machine on paper products
Nov 01 , 2021
In traditional production, paper products are pasted with water glue and tape. With the environmental protection requirements of the times, paper products are pasted and formed with hot melt adhesives, such as various paper boxes, cartons, express bags, handbags, etc. Electronic product packaging boxes, etc. To use hot melt adhesive, you need to spray it on the paper product with a hot melt adhesi...
Read More
-
How does the hot melt glue machine apply glue to the courier bag
Nov 01 , 2021
A layer of glue is applied to the seal of the express bag. Traditionally, double-sided tape is used. Now in order to improve product quality and production efficiency, hot melt glue and hot melt glue machines are used. So how does the hot melt glue machine apply glue to the courier bag? Paper courier bags not only need to be glued on the seal, but also need to be glued on the sides. The scraping m...
Read More
-
Fuse problem when using hot melt glue machine
Nov 06 , 2021
Each hot melt glue machine has a capacity limit. When the hot melt glue in the glue box is not less than 1/3, you need to add hot melt glue. The hot melt glue machine can add glue while working, just open the glue box to add glue while working. People who use hot melt glue machine equipment sometimes find the phenomenon of smoking. This phenomenon is a bad phenomenon and needs to be solved in time...
Read More
-
Hook loop tapes glue dispensing machine troubleshooting
Nov 17 , 2021
Troubleshooting Adhesive automatic hot glue dispenser machine does not run : 1. Check if the release paper is installed in place. The release paper holder is equipped with a material detector. When the material leaves the detector, the machine may not run 2. Check if the feed switch is turned on and the switch is out 3. Check whether the power supply is connected correctly No glue from the gl...
Read More
-
Clear ing Nozzle Assembly
Nov 18 , 2021
Clear ing Nozzle Assembly Nozzle will be jammed if filter assembly is blocked or broken, or if chars exist in hose/glue tube or nozzle assembly. Chars is formed because hot melt is overheated. Sometimes in these circumstances hose/glue tube and nozzle assembly need to be changed completely. Heat the nozzle assembly to desired temperature. -Minimize the air pressure of the cylinder pump of the hydr...
Read More
contact us
